Servicing · AMC · Panel Manufacturing
UltraBright Electrical and Services manufactures custom electrical panels, services switchgear and distribution boards, and takes care of the cabling in between. Clean workmanship, honest timelines, and engineers who know the equipment they are standing in front of.
What We Do
Most electrical failures announce themselves weeks in advance — in a thermal scan, a rising harmonic, a relay that trips a little too often. We find them while they are still cheap.
Inspection, cleaning, tightening and repair of existing boards, breakers and distribution equipment.
Custom electrical panels designed, fabricated, wired and routine-tested in house to your single-line diagram.
Scheduled preventive maintenance with a defined SLA, so problems surface on your calendar rather than at 2am.
Surveillance, access control and alarms — supplied, installed and maintained, with the cabling and power to match.
Building management and control integration — bringing electrical, HVAC and safety systems onto one interface.
Supply and installation of new equipment, and upgrades to switchgear that has reached the end of its life.
Panel Manufacturing
Every panel is routine-tested and supplied with its test report, GA drawing and wiring schedule.
Main distribution boards and LT main switchboards, with incoming and outgoing protection to your specification.
DistributionMotor control centres and power control centres for process and utility plant, with starters and protection built in.
ControlAutomatic power factor correction panels to cut penalty charges and ease load on your distribution system.
Power FactorFloor and zone level distribution boards, built to match the main panel and labelled for maintenance.
DistributionPLC-based control panels with the field wiring, interlocks and HMI integration your process needs.
AutomationAuto Mains Failure panels that sense a supply outage, start the DG set and transfer load automatically — then hand back when mains returns.
BackupWeatherproof low-tension kiosks for incoming supply control where there is no indoor substation room.
OutdoorPurpose-built control panels for pump sets, compressors and lighting circuits, wired to your control philosophy.
ControlMetering panels and automatic/manual changeover panels for reliable supply switching and accurate billing data.
MeteringHow Power Reaches Your Load
A typical low-tension distribution scheme. We build the boards, run the cable between them and maintain the lot. Hover a stage to follow the path.
AMF panels · utility to DG transfer
Incomer, metering and protection
Supply, laying, glanding and termination
SDB, MCC, APFC and lighting boards
Who We Work With
How We Work
No stage starts before the one before it is signed off. You get a document at every handover, not a phone call six weeks later.
We walk the site, list what is installed, thermal-scan the existing boards and tell you what condition it is really in.
Condition reportSingle-line diagram, GA drawing and a priced scope. No provisional sums that quietly grow later.
Drawings + fixed quoteFabrication, busbar work and control wiring on our floor, then routine testing before anything is loaded onto a truck.
Routine test reportInstallation scheduled around your operations, terminated, meggered and commissioned with your team present.
Commissioning sheetPlanned preventive visits under AMC, with a written report after each one and a response time you can hold us to.
Service recordsAbout Us
UltraBright Electrical and Services works at both ends of the same problem. We service and maintain the switchgear and distribution boards already installed in your building, and we manufacture the panels that replace them when it is time.
Because we do both, our panels are built the way a service engineer wishes they had been built — accessible, properly labelled, and easy to work on at three in the morning.
Talk to UsCareers
We are a small team and we are growing. If you are good with your hands, careful with your work and want to learn the trade properly, we would like to hear from you.
Control and power wiring, ferruling, busbar work and panel assembly on our shop floor.
Installation, cable termination, testing and commissioning at customer sites across Bengaluru.
Installing and maintaining surveillance, access control and building automation systems.
ITI freshers welcome. You will learn panel building and site work alongside our engineers.
Common Questions
Clients on an annual maintenance contract get a committed response window written into the agreement. For everyone else we attend as soon as a crew is free — call us and we will tell you honestly when that is.
Yes. Most of our servicing work is on panels and switchgear installed by somebody else. We will survey what is there and tell you what it needs.
It depends on the rating and on component lead times. Once the GA drawing is approved, a typical distribution board is a matter of weeks. We give you a date at quotation stage and tell you early if it moves.
The panel, its routine test report, the approved GA drawing and the wiring schedule. Everything is labelled so whoever maintains it next is not guessing.
Often that is the only sensible time. Shutdowns on live sites are usually planned for nights or weekends, and we schedule around your operations.
Contact
admin@ubelectricalservices.xyz
Applying for
Send your CV or résumé to the address below. Tell us briefly what you have worked on — that matters more to us than the format of the CV.
The button below opens your email app with the subject and a short template already filled in. Attach your CV and send.
Prefer to call? +91 96326 52309 or +91 85535 68617. No agencies.
